4/10/2012 10:39:09 AM
Topic:
Problem with scene and script
ecamarda
Posts: 5
|
Hola Diego, quisiera saber desde donde puedo configurar para que u na cortina, luz, escena, etc. se active automaticamente a una determinada hora y dia. Se que esto se puede hacer pero no encuentro desde donde. Desde ya agradezco tu respuesta.
|
|
|
3/30/2012 11:36:24 AM
Topic:
Mover una instalación de Habeetat Planner
Diego De Marco
Administrator
Posts: 33
|
Para quienes precisen mover una instalación de Habeetat Planner de una PC a otra, aquí explico los pasos:
1) Desinstalar Habeetat Planner en la pc "vieja". La configuración no se borrará, sino que quedará en la carpeta Solidmation, dentro de Archivos de Programa.
2) En la PC nueva, asegurarse de que Habeetat Planner NO ESTÉ instalado. Si está, es necesario desinstalarlo antes de continuar.
3) Copiar la carpeta "Solidmation" de la PC vieja a la PC nueva, en la misma ubicación (dentro de "Archivos de Programa").
4) Instalar Habeetat Planner en la PC nueva.
5) Registrar la instalación de la manera habitual. Luego de la registración, verán que los planos y el resto de la configuración serán los de la PC vieja.
Nota importante: si se utiliza una PC con Windows de 64 bits, la carpeta Solidmation estará dentro de la carpeta "Archivos de programa (x86)", en lugar de la habitual "Archivos de Programa".
|
|
|
3/30/2012 11:31:57 AM
Topic:
Moving Habeetat Planner to another PC
Diego De Marco
Administrator
Posts: 33
|
If you need to move Habeetat Planner to another PC, the steps are as follows:
1) Uninstall Habeetat Planner on the old PC. Your configuration will not be deleted. It will remain in the Solidmation folder, under Program Files.
2) On the new PC, make sure Habeetat Planner IS NOT installed. If it is, uninstall it.
3) Copy the "Solidmation" folder from the old PC to the new PC, in the same location (inside "Program Files").
4) Install Habeetat Planner on the new PC.
5) Register the new installation as usual. After registration, you'll find that all your plans and configuration from your old PC will be there.
Important note: if you are using a 64-bit version of Windows, the Solidmation folder will be inside the "Program Files (x86)" folder, instead of the usual "Program Files".
|
|
|
3/27/2012 9:31:42 AM
Topic:
Acceder a una NetCam
ecamarda
Posts: 5
|
Muchas gracias por la respuesta, seria bueno que actualicen el manual.
|
|
|
3/27/2012 8:17:10 AM
Topic:
Acceder a una NetCam
Diego De Marco
Administrator
Posts: 33
|
Hola Esteban. En la versión 4.2, el manejo de cámaras se hace directamente desde la solapa de dispositivos. Para agregar cámaras o DVRs, elegí directamente la opción "Nuevo dispositivo IP".
Saludos,
Diego
|
|
|
3/27/2012 3:15:54 AM
Topic:
Acceder a una NetCam
ecamarda
Posts: 5
|
Hola, acabo de instalar la nueva versión y cuando voy a Herramientas preferencias, no me aparece la solapa de Video. Me puedes indicar porque sucede esto? Muchas Gracias
Esteban
|
|
|
12/29/2011 1:00:54 PM
Topic:
Install 3160 mh
Diego De Marco
Administrator
Posts: 33
|
It's difficult to say. Usually you need to put the controller in setup mode (pressing the button for a few seconds) and then send any command (up or down) from Habeetat Planner. Also check the logs to see if the interface is working properly.
Cheers,
|
|
|
12/29/2011 12:59:19 PM
Topic:
Supported Interfaces
Diego De Marco
Administrator
Posts: 33
|
Hi Alex,
We're currently selling our HPA-2400 interface, which is Zigbee-compatible, and goes together with our products. We currently do not offer support for devices other than ours, plus PLCBus, Sonos, and various cameras. We'll be launching our Zigbee product line very soon (January 9th).
Cheers, and happy New Year!
Diego
|
|
|
12/29/2011 8:46:05 AM
Topic:
Supported Interfaces
Alex
Posts: 3
|
Hello,
i have allready running a PLC Interface.
I would like to install a wireless interface. But the solidmation interface is not certified for Europe at this moment.
So what kind of wireless interfaces are Supported by Habbeetat?
At the Preferences Menue i can just see PLC and Habeetat / Habeetat ZB.
Thanks & Regards
|
|
|
12/23/2011 2:56:44 AM
Topic:
Install 3160 mh
inmar
Posts: 2
|
Hey
I am tring to install the curtain plcbus controller 3160mh.
But when I definding the endpoint as curtain I can't send the address.
Any time I try to put the device on setup mode and sends close or open ,nothing happens.
What I am doing wrong?
Thank you
|
|
|
12/21/2011 5:06:54 AM
Topic:
Problem with scene and script
Diego De Marco
Administrator
Posts: 33
|
First make sure that your script is working correctly. From the script editor, you can run ths script step by step. Check to see if an error gets reported. The most likely cause is that you are referring to the endpoint as "Bathroom". Make sure that the endpoint has exactly this text "Bathroom" in the field "ID for scripts" in the endpoint properties.
|
|
|
12/21/2011 5:04:54 AM
Topic:
Zone Player
Diego De Marco
Administrator
Posts: 33
|
That's correct, this type of step allows you to instruct a Sonos Player to tune a particular radio station. You can see more about what Sonos players can do (really great stuff) at their website: www.sonos.com
|
|
|
12/9/2011 1:11:29 PM
Topic:
Zone Player
Alex
Posts: 3
|
Ok i´m sorry for that stupid question.
I think it is possible to stream webradio to a "Sonos" Zone Player. So it is only possible to stream to that device.
|
|
|
12/9/2011 1:09:47 AM
Topic:
Zone Player
Alex
Posts: 3
|
Hello,
i have a Problem with Habeetat Planner. When i try to insert a Macro i.e. al Radiostation i can´t choose a Zone Player. Can someone tell me what a Zone Player is? Is it just a softwareplayer für the streams?
Thanks & Regards
Alex
|
|
|
11/20/2011 12:40:37 AM
Topic:
Problem with scene and script
inmar
Posts: 2
|
Hey
First of all ,thank you of your amazing solution!
I have plcbus system ,with 1141+ interface and 2263 module.
I created the 2263 as a plcbus device endpoint "Bathroom".
I have defined successfuly the module with the address E1, and can control the endpoint in the "preview" tab.
The problem for me is when i try to use this endpoint in a scene or in a script - its just not responding to the commands.
In the script i writed :
function Main()
{
HP.Endpoints("Bathroom").Switch(true)
}
I definded a button that activate this script ,but when i pressed the button nothing happens.
What i am doing wrong ?
Thank you,
Inmar
|
|
|
10/19/2011 6:00:49 PM
Topic:
Residencial vs. comercial
frankn
Posts: 3
|
indicar en el texto del menu de registro de install nuevo que las licencias para casas son free, y que las comerciales no lo son. Hoy solo dice que son free.
|
|
|
10/19/2011 6:00:46 PM
Topic:
Residencial vs. comercial
frankn
Posts: 3
|
indicar en el texto del menu de registro de install nuevo que las licencias para casas son free, y que las comerciales no lo son. Hoy solo dice que son free.
|
|
|
8/19/2011 5:15:14 PM
Topic:
Servidor web
Diego De Marco
Administrator
Posts: 33
|
Hi,
Could you please remove the background and check? If you created the background as a separate image (inserting an image in the plan), it may be that this image appears "on top" of the other objects. The correct way to add a background is by right-clicking on the plan and use the option to set a background (NOT using the new image menu).
Could you please let me know which version of HomePlanner you're using?
Cheers,
Diego
|
|
|
8/19/2011 5:10:17 PM
Topic:
Servidor web
ruichaos
Posts: 1
|
Hi!
First I would like to congratulate you for this program. It´s good and easy simple to use.
Yet, when I click on the link that appears on Design, the browser only shows the background. This appens on the IE and Firefox.
Yours Sincerely,
Rui
|
|
|
8/16/2011 2:51:03 PM
Topic:
Render issue on non IE web browsers
frankn
Posts: 3
|
Please see attached files with an issue where the image is not rendered correctly (or at all) in the following browsers:
- Firefox
- Safari
- Chrome
It does show correctly on IE.
|
|
|